Just My Two Cents on Flowing Your Fuel Pressure

Steve Flowing Fuel Pressure Jets

Help with: Flowing Fuel Pressure Jets

Many have asked about flowing fuel pressure jets.  Asking what jet to flow their system with?  “Do I use a 70 “Holley” or a .073 “nitrous” jet?” Actually, these are the same. Nitrous jets are numbered in thousandths on an inch. Holley jets are numbered by drill size.

Most have heard that with a direct port system you should use the square area method. Take the jet size squared times the number of jets. Then take the square root of this number.

For example…

A system with eight .032 fuel jets is 32 X 32 = 1024. Then you take 1024 X 8 (jets) =8192. The square root of 8192 is 90.509, thus telling you that for the eight .032 fuel jets it wants you to flow thru a .090 jet.

Needless to say, the larger the fuel jets you’re using, the larger your flow jet gets! The larger your flow jet gets, the lower your regulator would read.  Fix this by adjusting the regulator back up in pressure, for the larger, more free flowing jet.

With each set of larger fuel jets you use, it’s going to tell you to raise the fuel pressure each time! This is an important bit of info when flowing fuel pressure jets.

A few things this method does not take into consideration, when flowing fuel pressure jets, would be;

  • Let’s try and use round numbers for the ease of this.. Let’s look at the average direct port system it has two nitrous solenoids with say .115 orifices in them. Then you have to fuel solenoids with .156 orifices in each of them. So that being said you can see that the nitrous solenoid starts out being smaller then the fuel side by over .040.
  • Then let’s take a look at the pressure the systems each run at. Again, for sake of round numbers we’ll say that you are using 1000 PSI on your nitrous pressure and 10 PSI on the fuel pressure. That being said, the nitrous is running at 100 times the fuel pressure!
  • Then let’s take the last piece of the puzzle and look at it. As far as nitrous to fuel ratio’s go many of you have heard us talking about running a N/F ratio of let’s say 6 to 1. Meaning you need 6 parts nitrous, to every one part of fuel..

Can you see where this is going?  You have fuel solenoids on each side of your engine that are already .041 larger then you nitrous solenoids, you are trying to force the nitrous through the system at roughly 100 times the pressure of the fuel side. Last but not least, you need 6+ times more nitrous than fuel to have a proper nitrous to fuel ratio! By design how is the nitrous ever to keep up with the fuel gains?

If you have a four jet spread (larger nitrous then fuel ) and a 5.5 PSI in fuel pressure and you start with a .024 nitrous and a .020 fuel jet as you work you way up to a .032 nitrous and a .028 fuel jet, the system gets richer with each larger jet change  –  just because your inching your way closer to the max area of the nitrous solenoids.

Think about this, how many times have you read where a guy say this solenoid won’t flow more than a .038 jet or a .042? Ever think that the solenoid isn’t the problem? Maybe the tune up or tuner is the issue? If you take your average .115 orifice nitrous solenoid ( area of .010386) and divide it into 4 jets it will mathematically flow at least 4 .057 (.002551) jets. But again, this doesn’t take into consideration the pressure drop across the solenoid either.

If you have an out-of-the-box plate system, in most cases, you may be better off to flow through the fuel jet your going to use in the spray bar. This is how most manufactures have chosen to set up their systems. That being said, when we flow a plate system and re map them we do this using a .073 orifice to flow through on all settings. Some do, some don’t!

If you’ve made it this far, I thank you for your time. Just my two cents on flowing fuel jets.

Steve Johnson
Induction Solutions


  1. Curtis Thomas says:

    Ok, but what about direct port systems??

  2. kevin penne says:

    good stuff on the flow, that’s the method I use. Im creeping up on my tune up and don’t want to hurt anything so im being cautious. Im running a pro fogger kit on a 496 with big m heads. last time out the car ran 9.33 with 22 jets on both and 6lbs fuel. im told to lean out the fuel because nos jets em way too fat. went to a 26 and was going to run the 22 on the fuel and keep the fuel preas the same for the test. 30 deg timing. Rite on or is that too mutch of a spread. thanks for your input . its like ask 10 people ya get 9 different answers ya know. for a 3400 lb car she does pretty good. Havin fun and wastein fuel. thanks Kevin.

  3. john monty says:

    im running a bigshot plate yea its ol school 103/93f 5.5 fuel enough through a 70 jet on the flow gauge?

  4. Mike says:

    What the point of bung welded into intake on fogger is it better thank just drilling the hole like the old days and screwing them in there pros and cons

    • Matt says:

      The bung is for a couple reasons. It allows for more thread engagement, much easier to set the depth of the nozzle as desired, and aims annular nozzles down the port as they should be.

  5. Todd smith says:

    If you would be running 4 kit a total of 1000 Hp shot what size fuel pump to feed just the Nitrous would you use

  6. Can I get a catalog book for nos?

  7. Joel Linville says:

    I just purchased one of your sledgehammer plate systems, I have a magnafuel fuel pressure regulator I was going to use but it looks like the small Holley regulator is what everyone uses, I tried one before and had trouble with pressure creep, do you sell a modified one that don’t creep or is the magnafuel ok, want to use the correct one.

  8. I recently purchased a race BBC engine that had an intake(fogger) that You folks designed..Upon doing sone work on it I noticed two issues..
    #6 nozzle was loose in the bung..threads seem ok…it would not go another turn to tighten..
    Second is the jets on a couple did not match the rest..is this normal?? Im new to all this..
    Can I get the tunes by providing You folks with either the owners name or stamping###??
    Really appreciate the help..

  9. Anthony says:

    Can you use the same jet and process for flowing a carburetor regulator?

  10. jimmy byrd says:

    I just had a speed shop build a new 427 chevy stroker they set it up for a up to a 300 shot so now how dose this work united speed built it just want an estmate from you to set up my fuel system and nitrios syatem and wether we go carb or efi 10 5 1 427 645 646 lift thanks jim

Leave a Reply to Anthony Cancel reply

Your email address will not be published.

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

2 × three =